The article author is making a few great pointers regarding A Step-by-Step Guide to Installing a Bathtub in general in the article on the next paragraphs.
Installing a bath tub isn't specifically rocket science, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the job can move quickly; if you have to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to vacate the old tub as well as set in the brand-new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed project, it is far better to take into consideration using one before you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will certainly help you mount a brand-new bath tub in your washroom if you have currently bought a new tub as well as do not need to change the arrangement of your previous water system pipes.
Your tools and material checklist ought to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the remaining water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the faucet in position with the maker offered backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the tub till the spirit level checks out level.
To install faucets, fit all-time low of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; then do the exact same for the various other tap.
Activate the water and examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill up the bath tub and additionally examine the overflow outlet and also the regular electrical outlet for leakages.
Lastly, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub must wait till the bathtub has been used a minimum of once as this will resolve it right into its last setting.
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall surface between the bath and the tiling, bring about problems with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealer can split rather early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly readily available on the market. It is advisable to fit the floor tiles making use of water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our article on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to browse our short article. Sharing is good. Helping others is fun. Thank you so much for going through it.
Free Quote